2 thoughts on “How does gold jewelry lose weight?”
Enrique
You can use wine essence to rub the gold necklace! The removal of the gold necklace, especially to clean the dust and dirt of gold jewelry, the easiest way is to brush gently with soft brush dipped in hot water. Scrub, but cut off particles (such as toothpaste, polishing paste, fine sandpaper, or fine sand cloth, etc.) to avoid reducing the weight of the gold and causing losses. . There is a trap with gold jewelry recycling 1. In terms of consumers, if you do not know the weight of gold jewelry in advance, it will inevitably fall into the trap without knowing it. 2. The recycling person will clean the gold jewelry. Usually, it will be burned first, and then soaked in the sulfate solution. This will only remove the surface impurities and will not have much effect on the weight of the jewelry. However, occasionally illegal vendors will put gold into the "king water" on the exclusion of impurities, which will dissolve the gold and cause "shrinking". This loss is often greater. . Avoid gold jewelry lighter 1. Consumers can check whether the balance of repurchase merchants has been verified by the measurement department. If it is verified, a green qualified verification logo will be pasted in obvious positions. 2. Because most of the golden repurchase points are usually not sent to the awareness of inspection, it can also be said to the gold jewelry jewelry supervision station before the gold is sold to make the weight in order to make it. 3. Finally, before cleaning the gold jewelry, the merchants can be required to weigh the gold jewelry. . The gold that you buy is called In the regulations, electronic balances should be equipped at each golden sales site, and these electronic balances must be verified and posted by the measurement department. Qualified logo. Therefore, in the process of purchasing gold jewelry, consumers can ask merchants to measure the jewelry, and to check whether the balance is verified.
Gold jewelry is to make a series of processes such as molding, welding, repair, and polishing. And it is hand -made, so some wear in the process of processing is normal. I can also suggest that you go to the jewelry store to "replace the old new" to make up a little manual fee to change the new decoration, so that you will save the loss caused by hand -worn wear.
You can use wine essence to rub the gold necklace! The removal of the gold necklace, especially to clean the dust and dirt of gold jewelry, the easiest way is to brush gently with soft brush dipped in hot water. Scrub, but cut off particles (such as toothpaste, polishing paste, fine sandpaper, or fine sand cloth, etc.) to avoid reducing the weight of the gold and causing losses.
. There is a trap with gold jewelry recycling
1. In terms of consumers, if you do not know the weight of gold jewelry in advance, it will inevitably fall into the trap without knowing it.
2. The recycling person will clean the gold jewelry. Usually, it will be burned first, and then soaked in the sulfate solution. This will only remove the surface impurities and will not have much effect on the weight of the jewelry. However, occasionally illegal vendors will put gold into the "king water" on the exclusion of impurities, which will dissolve the gold and cause "shrinking". This loss is often greater.
. Avoid gold jewelry lighter
1. Consumers can check whether the balance of repurchase merchants has been verified by the measurement department. If it is verified, a green qualified verification logo will be pasted in obvious positions.
2. Because most of the golden repurchase points are usually not sent to the awareness of inspection, it can also be said to the gold jewelry jewelry supervision station before the gold is sold to make the weight in order to make it.
3. Finally, before cleaning the gold jewelry, the merchants can be required to weigh the gold jewelry.
. The gold that you buy is called
In the regulations, electronic balances should be equipped at each golden sales site, and these electronic balances must be verified and posted by the measurement department. Qualified logo. Therefore, in the process of purchasing gold jewelry, consumers can ask merchants to measure the jewelry, and to check whether the balance is verified.
Gold jewelry is to make a series of processes such as molding, welding, repair, and polishing. And it is hand -made, so some wear in the process of processing is normal. I can also suggest that you go to the jewelry store to "replace the old new" to make up a little manual fee to change the new decoration, so that you will save the loss caused by hand -worn wear.