How can I buy Casa Di [C1HDU85G3] how to solve the problems!

Saudi [C1H85G3] Question and solution:
1, more than water inlet
) Generally, the water inlet valve core is stuck. This situation first replace the water inlet valve;
) If the failure is not resolved, the problem is in the water level switch, the water level switch can be stopped, and the water can be stopped. At this time, the water level switch should be replaced; should be replaced; R n) If the pressure tube is worn over a long time or the pressure tube is in poor contact with the water level switch and the outer bucket air, it can cause the water leakage. The switch is not moved and misunderstood as the water level. At this time, the pressure pipe should be checked whether the pressure tube is worn or whether there are poor contact or departure at the two connections;
) The mouth causes the pressure to reach the pressure switch. At this time, the large nut should be unscrewed, and then the inner barrel should be taken out to remove the foreign body blocked by the gas mouth.
5) If everything is invalid, change the computer board, because everything is controlled by the computer board.
2. Do not enter the water
1) Connect the power, the ears are close to the water inlet valve, if there is, if so, check whether the tap water breaks the water, turn off the faucet, and spin the water inlet pipe joint joint Check whether the filter of the water inlet valve is blocked. If the filter is pulled out for cleaning, if the problem has not been resolved, the water inlet valve may be changed. The water inlet valve did not: "buzz". At this time, you can try to change the computer board. The problem may be on the computer board.
3. Do not dehydrate
) First check the safety switch, the washing machine connects the power program to the dehydration state, and the safety switching arm is pressed by hand or tools to minimize. Seeking "E1", at this time, the safety switch or computer board should be replaced;
) If the safety switch is pressed by hand or tools, it can be dehydrated normally, indicating that the power -off distance of the safety switch is relatively low. At this time, the safety switch should be replaced;
) If only the pulsator turns in the inner barrel when it is dehydrated. The loosening and wear of the steeper rod on the valve causes insufficient opening distance. At this time, the distance of the adjustment rod should be adjusted to enable it to separate the clutch's claws and spiny wheels;
4) If it is dehydrated, turn off the machine and turn off the machine. In the case of the lid, the water level sensor is poor or welded, causing the computer board to mistake the drainage time, and the bee will call the police. At this time, the water level sensor should be replaced;
4, no drainage
) The tuning rod nut is not loose, which causes the traction device to unable to pull the drain valve core and cause no drainage. At this time, the nut is fixed to open the drain valve core;
) Suo Wei Song can be damaged, the traction device is damaged, and the drain valve core cannot be opened. At this time, the traction device should be replaced;
) There may also be debris in the drain valve to block the drainage. Drainage valve cover, take out the debris;
4) If it is not resolved, the computer board may be damaged, and the computer board should be replaced.
5. Wash the sound of sound
) First distinguish the sound from which location comes from. When I did n’t pay attention when I was laundry, there were small things such as coins in the clothing pocket that might be along the question of the wave wheel and the inner barrel. If you can't take it out, you can easily remove or remove the inner barrel if you can't take it out. It is also necessary to warn users that when washing clothes, you must take out the coins in your pocket.
) If the sound is emitted from the bottom, the problem may be on the motor or clutch. At this time, you can get a triangular belt and then run through. If the noise is eliminated, it means that the clutch has been damaged. On the contrary, the problem of the motor should be replaced.
6. There are noise of dehydration
1) First check whether the barrel underwear is placed unilateral, put away the dehydration and shake, and there is a murmur. At this time 2) In the same way as a murmur as a noise, check whether there is a foreign body between the inner barrel, the wave wheel and the outer barrel. The distance is not enough, so that the clutch's claws and spiny wheels are wiped when the phase is rotated. At this time, the position of the adjustment rod should be adjusted;
) Otherwise, the problem is on the motor or clutch.
7. Can't connect to the power
1) If you press the power switch and the power switch is immediately jumped up, the power switch may be damaged, and the power switch should be replaced;
) Power supply may be kept by key booking or damage to the computer board;
3) It may be because the user is not used properly, which causes the computer board to get water or wet, causing the inside of the computer to move due to short circuit. Cut off the power supply, and the computer board should be replaced at this time.
8. Enter water and drainage
1) First check whether the drainage valve core is stuck in the power off state, and you can see if the valve core is in place. Otherwise, the internal spring may be stuck. At this time The valve cover should be unscrewed, and the foreign body stuck or damaged should be replaced.
2) If the drain valve is normal, check whether the traction rod of the traction device is in place, and whether to pull and return the led rod with the hand, if there is a stuck, it means that the internal damage of the tractor should be replaced;
3) If the traction device is normal, the traction device is already moving in the water inlet state, and the shake and drainage valve core is drained. This shows that the computer board program is confusing and the computer board should be replaced.
9. Dehydration weakness
1) First check whether the belt has been worn, and the method is pinched with both hands. If the straps on both sides can bump, it means that the belt has been worn. At this time, you can adjust the position of the motor and tighten the belt. , But if the belt is too powerful or the position of the motor is not solved, the belt should be replaced;
) If the belt is normal, the capacitor should be replaced at this time;
) On the computer board, the thyristor of the control motor has been damaged. At this time, the voltage can be measured normally when the motor is running. If it is abnormal, the computer board should be replaced;
4) The motor is damaged, and the motor should be replaced at this time.
5) The diameter of the clutch square wire twist spring becomes large rust, so that the square wire twist spring cannot hold the dehydration shaft to drive the bucket to run normally.

Known as a high -end brand, he can only be huh. In the case of up drainage in the drum washing machine, Casa Di does not know why the drainage is used. Even if the padding is raised, the water in the tube cannot be discharged, which is completely the designer's wind. In addition, Casa Di's refrigerator, after 2 years, the frozen chamber drawer is automatically opened like crazy, which is completely programmatic. How to create a high -end brand with such unreliable quality stability and testing technology? Not to add a few new features, play a little gimmick or innovation! The key of a century -old brand is stable and reliable quality! Intersection Intersection It's not that I don't love the national brand, it is a bit miserable. Among the digital home appliances I used, the biggest pits are Casa Di.