brass jewelry wholesale The ribbon binding method of the packaging gift box

hood jewelry wholesale No matter what items, even if there is no wrapping paper or box, it is not packed in a bag. As long as a ribbon is tied, it will turn into a gift incredible instant. The content of the ribbon tie method of the packaging gift box compiled by everyone, I hope everyone likes it!
— the basic method of the bow of bow n, no matter what items, even if there is no packaging paper or box, it will not be installed in In the bag, as long as a ribbon is tied, it will turn into a gift incredible moment. If you hit a beautiful bow, you will immediately add the charm of the gift itself.
The system method of bow:
1. Put the two ends of the ribbon one knot
2. Hold the middle position with your hand and bend the silk on the right from time to a circle
3. Fold the ribbon on the left from the top, hold the thumb of the right hand, hold the
4. Excede from the upper upper ribbon circle of the right side, and then pass through the circle of the left ribbon to the
5. The ribbon circle on the right side is placed on the left, and the ribbon passed through the circle around the left ribbon is tightened on the right
. The two ends of the ribbon are trimmed into a favorite shape, and the bow is the bow. Completed
(2) -The system method of turning over the bow
This is a bow that uses positive and negative sides. Outside
2. Folding the petals on the right
3. The petals folded on the left are longer than the right. 5. Put out the long side from the hole
6. Sort the sorting of the same size
7. Cut the ribbon into the appropriate length according to the size of the bow, complete
(3) - Basic basics The cross -shaped ribbon system method
This is the most basic ribbon system. When the position of the cross changes, the feelings expressed by the gift will also change. It can be changed to the card or small items to change the fun in the base to experience the fun in the foundation. The cross -shaped ribbon is very concise, which can set off the grace of the gift itself.
This of the ten -shaped system
1. Prepare a total of 4 times the total length than the box of the box. This is the necessary length of the bow. , Leave the length of the bow knot, then take a circle vertically
3. Turn it to the middle part, two ribbons cross the horizontal direction, and then circulate horizontally
4. Keep the initial first stay. The good ribbon is wearing it in the past
5. The ribbon worn from below is knotted, and then tied it
. In this way, the simple and beautiful bow will be as good as
(4) - Basic double -inclined wire ribbon system method
This is a very attractive ribbon system that can express the grace of gifts. Except for the simple cross
, the dual -inclined line method
1. Preparation of the long wide high combination of the box with a total of 3 times the ribbon. Leave enough length to use the bow
2. Put the ribbon tilt in the figure
3. Pay attention to putting the diagonal ribbon into parallel shape, then roll it up
4. Put the ribbon on the left through the ribbon on the right crossing
5. Play a beautiful bow
6. In this way, the front and rear sides can form two parallel diagonal ribbons
(5) - The basic V -shaped ribbon system method
V -fiberic system method gives people a very beautiful, clear, and sophisticated feeling. When using a gift to the beauty, men or elders, it will achieve the effect of surprising victory.
V glyph system method
1. Preparation of the long wide height of the box, 4 times the total length of the ribbon of the ribbon
2. Leave the necessary length of the bow. According to the picture, one circle is cleverly oblique
3. The picture shows it through, and fix the
5. Bend the ribbon that is worn from below into a round shape and knot it. In this way, the beautiful V -shaped knot is completed.
(6) - Basic basics The square sugar -type packaging method
The square sugar -type packaging method of the tidy -square items
1. Cutting the packaging paper is the length around the box 2 ~ 3 cm, and the width is the width of the box 3 cm. The bottom of the box is placed in the center of the paper
2. Fold the paper on the right along the box inward, and keep the edge of the paper in the center of the box
3. Then fold the paper on the left inside intoward
4. Use transparent rubber or double -sided tape to fix the paper overlap at
5. Paper on both sides is folded inward inward
6. Fold the paper into beautiful ones in order. Cableform
7. Gently marked on the transfer of the origami at the upper and lower origami. Fix the junction, wrap the other side, turn to the front of the box, decorate it with a ribbon or flower, and complete
(seven) - The basic tilting packaging method is thin gift box
This is the most the most One of the basic packaging methods. Use paper to pack the gift box from a certain angle, and you can wrap the corner in order. After being proficient, the package gifts will become very simple. Mastering this method is useful.
The tilt packaging method of thin and thick gift box
1. Prepare paper, as shown in the figure, fold the paper along the edge of the box to the inside, so that the corner of the paper is located above the lid
2 2 2 Then fold the paper in the back to ensure that it is appropriate to cover the box. If you cannot meet the conditions of 1 or 2, the paper size does not meet the requirements.
3. Press down the folding corner above, fold the paper on the left, and clean the excess paper to the inner side
. Fixed, fold the paper in the rear or slowly support the box
5. While sorting the excess paper, turn the box inward
6. The paper on the right can be used. The same way as the left side, keep the paper inward inward
7. The remaining paper should be folded inward, and the remaining n 8. Finally, the excess corners to the interior are inward to the interior Fold it, just fix it with double -sided glue, and then tie a good ribbon on the box.
(8) - The thick gift box of the basic tilt packaging method
In the box to prevent the tilt of the box, this uses this. The packaging method is very convenient to pack the box.
The packaging method of a thick gift box
1. Prepare paper. First of all, as shown in the figure, the front of the box faces out, fold the paper in front of you, cover 3 horns
2. Second, as shown in the figure, in the same position, the external paper on the outside is shown. Fold and confirm whether the corners of the 3rd side are covered up. You must meet the conditions of 1 and 2 before you can go down
3. Wrap the front of the box in front of the paper. On the left and right corners, fix the tape after the corners are tidy
4. Press the position as shown in the figure, and then pour the box and the packaging paper to the outside
5. The paper on the right side is also on the right side Similarly, the corner of the box is folded, and then like the left side, the corner of the box is folded outward, and the corner of the box is fixed with tape. Fold the excess paper inward and pack the front
6. Fold the paper under the right side to form a neat folding line to close the corner of the box. Fix it with a tape, then organize the front
7. Fold the outer paper on the side of the body, fold the excess paper along the edge of the box, fix the edge with the tape
8. Turn the box over the box To the front, the packaging is completed, tie the ribbon or decorate.